Synthesis and characterization of carbon nanotube-quicklime nanocomposites and reduced graphene oxide hybrids for screen printed electrode modification

• 第一著者: Ibrahim, Ruzanna
• フォーマット: 学位論文
• 言語: English
• 出版事項: 2019
• 主題: Nanocomposites (Materials); Graphene; Electrodes
• オンライン･アクセス: http://psasir.upm.edu.my/id/eprint/91075/1/ITMA%202020%203%20IR.pdf; http://psasir.upm.edu.my/id/eprint/91075/

Carbon nanomaterials such as carbon nanotubes (CNT) and reduced graphene oxide (RGO) have become the materials of interest due to many desirable properties. A nanocomposite containing both CNTs and calcium oxide (CaO) or quicklime is beneficial since the high conductivity of CNTs are favourable for electrochemical detection and CaO may increase thermal stability. Additionally, it has been shown that the performance of CNTs or RGO alone in applications such as electrochemical detection is constricted due to agglomeration of both materials caused by - interactions. Decorated nanomaterials and nanomaterial hybrids have also demonstrated better performance as sensor platforms compared to the base materials. In this work, CaO-supported catalysts (Ni/CaO, Co/CaO and Fe/CaO) were used to synthesize carbon-nanotubes quicklime nanocomposites (CQNs) via chemical vapour deposition (CVD) of hexane with studies on the effects of catalyst composition and CVD temperature. The CQNs were then characterized using X-ray diffraction (XRD), Raman spectroscopy, nitrogen adsorption desorption isotherms, field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and thermogravimetric analysis (TGA). Various RGO hybrids were also prepared including RGO-carbon nanotubes quicklime nanocomposites (RGO-CQN), RGO-carboxylated multiwalled carbon nanotubes (RGOMWNT) and RGO-silver nanoparticle hybrid (RGO-Ag). The RGO was synthesized using the improved Hummer’s method followed by reduction using hydrazine. RGO and silver nanoparticles hybrids (RGO-AgNPs) were synthesized via the reduction of GO and silver nitrate (AgNO3) using a combination of hydrazine hydrate and sodium citrate. RGO-Ag were characterized using XRD, FESEM, TEM, UV-Vis and FTIR. CQNs modified screen printed carbon electrodes (SPCE) and RGO-hybrids-modified SPCE were subjected to cyclic voltammetry (CV) studies with potassium ferricyanide (K3Fe(CN)6) redox probe in order to see their potential use in electrochemical detection. Using Ni/CaO (10 wt%) (800 °C), Co/CaO (15 wt%) (800°C) and Fe/CaO (20 wt%) (850 °C) catalysts produced CQNs with the highest graphitization possessing IG/ID values of 1.30, 1.15 and 1.36, respectively. As SPCE modifier, the CQNs showed relatively high CV response compared to the bare electrode namely HNi10-800, HCo10- 800 and HFe15-900 as indicated by their high anodic peak current values and low peakto- peak potential separation, ΔEp. However, graphitization can be correlated with high electrochemical performance only for Ni/CaO and Co/CaO catalyzed CQNs since for Fe/CaO catalyzed CQNs other factors may attribute to the electrochemical performance. When compared to MWNT-modified SPCE, the CV response of the HNi10-800- modified and HFe15-900-modified SPCEs displayed comparable electron transfer and they also exhibited higher anodic peak currents. Both RGO-CQN nanocomposites (RGO-HNi and RGO-HFe) showed increased CV response when they were used to modify SPCE. It can be seen that the modification of SPCE using RGO-CQN show better electrochemical response than using only RGO. It was also found that the RGO-CQN-modified SPCEs presented higher electroactive surface area compared to RGO-MWNT-COOH modified SPCE. The AgNPs grown on the RGO-Ag hybrids as observed from TEM and FESEM micrographs were polydispersed with the lowest mean diameter of around 20 nm for RGO-Ag5 (5 mM Ag). RGO-Ag10-modified SPCE displayed the highest CV current for all RGO-Ag synthesized in this work, presumably due to its better reduction and well dispersed AgNPs. However, RGO-Ag were found to be unstable on the SPCE surface. Meanwhile, RGO-Ag/MWNT-COOH-modified SPCE showed slower electron transfer due to significant increase in the peak potential separation but the stability of RGOAg/ MWNT-COOH on SPCE is better compared to RGO-Ag. Based on this work, the suitable material for SPCE modification would be CNTQuicklime nanocomposite synthesized using Ni/CaO (HNi10-800) and Fe/CaO (HFe15- 900) and RGO-CQN as they presented relatively high CV currents and low ΔEp values indicating fast electron transfer. It is anticipated that the carbon nanomaterial-modified electrodes from this work can be used for the electrochemical detection of heavy metal ions.